SKU: 102F
102F, camera traps hunting camera security Falcon with MMS function+3G
0 %s αξιολογήσεις
248.60€
Out Of Stock
  • Rating:
  • Manufacturer:
  • Model:
    102F
  • Νυχτερινή Όραση:
    Support
  • Ανάλυση Βίντεο:
    1280x1080
  • Διαθεσιμότητα 3G:
    Ναι.
  • Line input :
    AV output
  • Απόσταση εγγραφής άνεσης:
    12 - 15m
  • Show all attributes
248.60€
Out Of Stock

Camera trap Falcon + MMS 3G not expensive variant of the "forest" cameras working at the motion sensor with the function of MMS. It is the ability to send photos, not only on phone but also by e-mail and distinguishes it from a younger model: Falcon + MMS. Its customization will not take You much time, in fact all the device menu is in Russian language. To get started with the camera you need to purchase an SD memory card (USB flash drive 8 to 32 Gb) and SIM card (Beeline or MTS). For ease of use as a forest camera-trap is supplied with a special clamping strap housing camera traps to trees. Kopus the device tight and protect from any environmental influences the internal elements of the camera traps.

Camera trap Falcon + MSS-3G can shoot in total darkness up to 20 meters with lights out of 54 infrared emitters. The work of these emitters hidden to human eyes (including animals) and not attract attention. To further disguise the device has a protective forest color.

The principle of operation of any camera traps is the ability to produce videophotoshop motion, recorded using special cameras sensors in range in front of her. Using a thin camera settings you can clearly adjust the camera for any needs.

The new firmware brings the device to a new level. With this add-on device can send to Your mobile phone an MMS message with a photograph in real time, attacks the same email with the same photo. Simply put, at the time of activation of the motion sensors, the camera trap not only save a photo and shoot video on the SD card, but at the same time send an MMS message with a picture of what is happening on one or more phones and electronic e-mail addresses.

Easy control

Remove the battery compartment cover. Make sure that the power switch is in the OFF position, place a fully charged lithium battery into the battery compartment. Insert the cover into place. At the expiration of 3 minutes, during which did not commit any actions in the Test mode, the camera automatically turns off to conserve energy; it may be included in case of motion detection.

If the battery is low, the camera automatically turns off. Change the battery in time.

Insert the SD card

Insert the SD card in the card slot marked side up. Please note that an SD card can be inserted only in one direction. Make sure switch write-protect the SD card is in the position "recording".

Turn on the power ON mode ("enabled")

Before you turn on the camera, note the following:

Avoid temperature extremes and sudden movements, which can be interpreted as movement of an animal or person, for example, trees, which can cover from direct sunlight most of the day, or any other source of heat. Such factors can become false signals.

The height of the camera above the ground should be at 1 meter. For example, the level of the back of a deer is sufficient to install the camera. Generally, the preferred height is one to two meters. Slide the power switch to the ON position to turn on the camera and enter the mode to ON.

After the camera is turned on, within 15 seconds will blink the led indication (red). 15 sec is the time settings for automatic shooting photos and videos, for example, to close the bottom cover to lock the camera on the tree and stand back. Mode ON the camera will capture photos and videos automatically in accordance with default settings or last user settings. The camera can record the sound, so the video is recorded with sound (optional).

Go to TEST mode

Slide the power switch in the TEST position to enable TEST mode. In the test mode has several functions: custom settings, manual capture, preview.

Customizing

Press the MENU button to enter the settings menu. The camera can be set manually by setting the settings on the camera screen or on the TV screen. Detailed control is described in the section "Additional control".

Manual shooting

Press shutter to manually capture photos and videos.

View images and videos

Images or videos can be viewed in two ways: On the LCD screen of the camera. On the TV screen connected to the camera via cable.

Press right to select viewing of pictures on the camera screen or TV will be shown on the last picture. Press "up" to view the previous pictures, down the next. Detailed steps: remove the shots or videos will be described in the section "Additional control".

Off

Slide the power switch to the OFF position to turn off the camera. Attention, even when switched off, the camera consumes a certain amount of energy at the level of µA.

Therefore, it is necessary to remove the battery if the camera is not used for a long time.

Additional settings

Of the main camera settings discussed in the previous section, we know that the camera has three basic operation modes:

1. OFF mode: the power switch in the OFF position (bottom).

2. ON mode: power switch in the ON position (top).

3. TEST mode: power switch in the TEST position (middle).

Of these three modes, the OFF mode is the safe mode if you need to replace the SD card or battery and for carrying camera.

This section discusses additional management of the camera settings. Settings can only be set in the TEST mode.

Basic settings

The configuration steps for the following menu items: camera mode, photo size, video size, burst shooting, movie length, delay, timer and GSM mode.

Configuring camera mode

There are three camera modes: Camera, Video and Camera+Video. Camera mode is configured in the settings menu. The following shows how to set camera mode to Video mode, if previous mode was mode Photo:

a) Press MENU to enter the settings menu.

b) Press DOWN (down) to select mode.

c) RIGHT Click (right) to choose the Video.

d) Press down to select the item to save the current settings. Press MENU to cancel settings and return to the information window.

Formatting the SD card

After formatting SD card the system will delete all photos and videos that were stored on it, make sure you have backed up your important data.

a) Press MENU to open the settings menu.

b) RIGHT Click (right) to select system settings.

c) push DOWN (down) to select format.

d) RIGHT Click (right) to select the SD card.

e) Press down to select Enter to go to the submenu.

f) Press down to select OK. OK will be highlighted.

g) Click OK to start formatting the SD card. During formatting, the screen will display the message "wait" as below. Press MENU to cancel setting and return to the information window.

Customize photo size

The option has three values::12MP:8MP and 5MP. The default value is 5 mega pixels. Below shows how to specify the size of 5M pixels:

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select Resolution

c) Press right to select 12M pixel

d) Press DOWN (down) in order to select and save the current settings , then press menu to return to the information window . Press MENU to cancel setting and return to the information window.

Adjust the video size

This parameter has three values: 1080P, WVGA, QVGA. The default value is 1080P, the following shows how to set 720P video size , if the previous setting was WVGA :

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select the Resolution.

c) Press RIGHT to select WVGA

d) Press DOWN (down) to select and save the current settings, then press menu to return to the information window.

e) Press MENU to cancel setting and return to the information window.

Setting the date and time

You can change the date and time on the device by adjusting the setting if necessary, e.g. after you change the batteries. Date format: day/month/year, time format: hour: minute: second. Year value: from 2010 to 2050.

For example, you must set the date and time: November 15, 2011 half past ten, the steps are the following:

a) Press MENU to open the settings menu.

b) Press right to open the “system”

c) push DOWN (down) to select date/time.

d) Press right to display the setup date/time press the UP (up) and DOWN (down) to change the value

e) Press down to select and save your current settings, then press MENU to return to the information window. Press MENU to cancel setting and return to the information window.

Setting continuous shooting

This option controls the number of pictures in each shooting mode the camera. Here there are four values: "1 photo", "photo 3" "6 photos" and "9 photos". The default value is "1 photo". Below shows the steps for setting up a series of 3 shots, assuming that was a value of 1 photo:

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select Multi (series).

c) RIGHT Click (right) to select a series of 3 shots.

d) Press DOWN (down) to select and save the current settings , then press MENU to return to the information window. Press MENU to cancel setting and return to the information window.

ISO settings

This menu may be needed only in the improvement of night photography, there are 3 values: 100, 200, 400.

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select the duration of the video

c) push DOWN (down) to select and save the current settings, then press MENU to return to the information window. Press MENU to cancel setting and exit.

Setting the duration of video

Below shows how to set the duration of video of 30 seconds provided that the previous value was 10 seconds:

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select the duration of the video

c) push DOWN (down) to select and save the current settings, then press MENU to return to the information window. Press MENU to cancel the current settings and exit.

Audio setup video

Below shows how to mute video:

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select the Voice (voice).

c) RIGHT Click (right) to display the VOICE settings screen.

Set the interval

This parameter indicates the time duration for which a passive infrared motion sensor (PID) will be disabled after each switch the camera ON. During this time PID the device will not respond to the movement of the person (or animal). The minimum interval is 5 seconds, that means PID works all the time and the shot goes almost continuously. The maximum interval is 30 minutes, which means that PID will be active for 30 minutes after each activation. The default value is 5 seconds.

Below shows how to configure time interval between PID 1 minute, provided that the previous value was 5 seconds.

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select the interval.

c) RIGHT Click (right) to select the settings of interval.

d) Press DOWN (down) to select 1 minute.

e) Press DOWN (down) to select and save the current settings, then press MENU to return to the information window. Press MENU to cancel setting and return to the information window.

Timer setting

This parameter specifies a period of time of the day when the camera turns on. The rest of the time the device is turned off. Valid values range from 0 to 23 (hours) 0 to 59 (minutes).

For example, the camera has to work from 8 am to 5 PM, then the settings will be the following:

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select timer.

c) RIGHT Click (right) to select position, press the UP (up) or DOWN (down) to change values at 8 and 17.

d) Press DOWN (down) to select and save all current settings, then press MENU to return to the information window. Press MENU to return to the previous menu.

Password

If you enabled the password after switching on the camera, the camera screen will be prompted for a password. By default this feature is disabled. To change the settings as follows:

a) Press MENU to open the settings menu.

b) Press DOWN (down) to select Password.

c) push Up to activate, then press right to set the password of 4 digits

d) Click OK to save all current settings, then press MENU to return to the information window.

e) On LCD screen you will be prompted for a password next time you turn the camera on. Press MENU to cancel setting and return to the previous menu.

Playback

In playback mode, you can view or delete pictures or videos. The pictures and videos you can view on the camera screen or TV, which connects to camera with TV cable. For simplicity, work with a PC here not described.

Viewing photos and videos

a) Navigate to TEST mode and open the information window.

b) Click to the right to view the latest pictures (or video) on the camera screen, TV or using the program image viewer.

c) Click to the left to begin watching the video

d) Press left again to stop playing the video.

e) Press up to view the previous photo (or video) and DOWN (down) to view the following.

f) Press DOWN (down) to return to the information window.

When viewing the images will be displayed accordingly the total number of all images on the SD card and the number of the opened image.

Deleting photos and videos

The sequence of actions is the following:

a) Press right to display photos and videos.

b) Press Menu to select Delete (delete).

c) Press right to select and delete the current or all.

d) Press OK, cancel (Cancel) or confirm (OK).

e) Click OK to delete the picture or video.

Press cancel to cancel, then press MENU and DOWN (down) to return to the information window

Note. After removal of the image file or video, deleted files cannot be recovered! To delete all images and video clips on an SD card, it is recommended to format the SD card

Laser pointer (optional)

Laser pointer can be turned and is particularly necessary when in the dark you must specify the object or a specific region (ROI).

Click﹡ to turn the light on in the TEST mode and control the transverse slope on the back side of the camera adjust the angle of the shooting direction. NOTE: please note that the laser is dangerous to the eye, if made available to the human eye.

File numbering

Images and video are saved separately in a specially created folder with the name (104MEDIA). The file number is formed by adding one to the last number each image or video. The name of the saved file will look like this: PTDC0001.JPB or PTDC0001.AVI. By extension, you can define an image for it (the extension .jpg) or videos (extension.avi).

Firmware update

The camera has a function of automatic updates. The update is only necessary if the best available version of the firmware. The sequence of actions is the following:

1. Unzip the update file

2. Copy FW18NA.bin on the SD card.

3. Insert the SD card into the camera.

4. Turn on the camera (mode Test).

5. The camera will read the file and perform the update automatically.

6. When you upgrade the camera's screen will be black

7. Remove the SD card, then insert it in the computer, delete the file FW18NA.bin on the SD card. (If you do not delete this file, the camera will start again the update mode when switched on).

8. Insert the SD card into the camera to work with it.

Νυχτερινή Όραση Support
Ανάλυση Βίντεο 1280x1080
Διαθεσιμότητα 3G Ναι.
Line input AV output
Απόσταση εγγραφής άνεσης 12 - 15m
Email photo yes
Αισθητήρας Κίνησης Support
Matrix CMOS
A/C DC12V
Διαγώνιος επίδειξης 2,5"
Έλεγχος εκφόρτισης μπαταρίας yes
Μέγεθος μνήμης up to 32 GB
Μπαταρία 2000mAh
Γωνία 60 °
Λειτουργία MMS yes
Υποστήριξη MicroSD yes
μπαταρία 3 months
Λειτουργικό σύστημα Windows 98 / 98SE / ME / 2000 / XP
Εξοπλισμός Tsifrovayafotolovushka 1x 1x 1x AC 110-240V Battery Charger 1x 1x USB-cable A / V cable 1x CD 1x belt

No questions.

Get 3% OFF on your purchase! Like, Share, Tweet or Follow us and get Discount!